
12V 1.2KW Starter Motor 28100-0D020 for Chevrolet and Toyota
Applicable models:Chevrolet, Toyota Leister Corolla
Reference part number:28100-0D010 17737 2280006660 STR-8102 LRS02435 ST1429 281000D020 228000-868 228000-6660 228000-6860 28100-0D010 228000-6662 28100-0D020
| Power horsepower : | 12V 1.2KW |
| Number of feet : | 9T |
| Size : | |
| Weight : | 净重3.5KG |
| Packaging : | Neutral kraft paper packaging |
| Spot/Pre sale : | Spot goods |
| Warranty : | 1 year |
| Product number : |
| Type : | starter |
| Specification : | 12V 1.2KW |
| Number of feet : | 9T |
| Brand : | NUOJIN |
| Number : | 28100-0D020 |
| Quality : | NEW |
| Delivery time : | 30 days |





Overview of the 28100-0D020 Starter Motor
The 28100-0D020 starter motor is a 12V, 1.2 kW unit that serves a range of small petrol engines in Chevrolet and Toyota applications, including models built on shared platforms. It is a compact reduction-gear starter with an integrated solenoid, and it is commonly cross-referenced with the 228000-6660 and STR-8102 families. Hejian Nuojin Auto Parts Co., Ltd. supplies it as a complete replacement unit for workshops and parts distributors.
About the 1.2 kW Rating
Small four-cylinder petrol engines need less cranking torque than diesels, so a 1.2 kW starter is enough to turn them at the speed the engine management system expects. That speed matters more than drivers realise: below a certain cranking rpm the ECU will not enable injection, and the engine turns over without firing.
When a starter loses output through worn brushes or a burnt solenoid contact, the engine may still crank but not start on the first attempt, which sends owners looking for fuel or ignition faults. A cranking voltage and current test will show whether the starter is drawing more current than it should.
Reference Numbers and Cross References
- 28100-0D020 and 281000D020
- 28100-0D010 and 281000D010
- 228000-6660, 228000-6662, 228000-6860 and 228000-868
- STR-8102
- LRS02435
- ST1429
- 17737
These references cover more than one engine variant, so the number on the old starter is the reliable identifier. Where the label is unreadable, compare the pinion tooth count and the terminal bracket position with the photographs before ordering.
Construction and Service Life
The drive end housing is cast aluminium and carries the pinion bearing, keeping the pinion square to the ring gear. A reduction gearset multiplies motor speed into cranking torque, and the gear cavity is packed with high-temperature grease that stays in place through repeated heat cycles.
The solenoid is sealed against dust and spray. Terminal studs and the main lug are plated for corrosion resistance, which matters on vehicles used near the coast or in markets where roads are salted in winter. The brush plate uses a heat-stable moulding that does not distort when the starter heat-soaks after a hot shutdown.
What Usually Fails First
- The solenoid contact, which burns after thousands of switching cycles
- Brush length, especially on cars used for many short trips
- The pinion drive clutch, which starts to slip and produces a whine under load
- The front bearing, which dries out and lets the armature run off centre
- Corroded terminals, which reduce available cranking current
On this starter family the solenoid contact is the most common failure. If the motor bench tests well and the contact is burnt, a solenoid replacement is a legitimate repair, but on a unit with more than a hundred thousand kilometres of starting cycles a complete replacement usually works out cheaper over the following years.
Fitting the Replacement
Disconnect the battery negative terminal. Remove any intake or bracket that restricts access, disconnect the main cable and the solenoid signal wire, and support the starter before removing the mounting bolts. Clean the bell housing face and check the ring gear through the aperture.
Fit the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Reconnect the battery, crank briefly and listen for clean engagement and release. If the engine cranks but does not fire, check that the signal wire is on the correct solenoid terminal before assuming a fault in the new starter.
Quality Control and Supply
Hejian Nuojin Auto Parts Co., Ltd. bench tests each starter for no-load current draw, solenoid pull-in and release, pinion throw and running noise. Units are packed in neutral cartons with foam protection, standard references are held as spot goods, volume orders are delivered in around 30 days, and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does this starter fit both Chevrolet and Toyota models?
It is listed for applications from both brands that share the same starter family. Confirm the number on the original unit, because engine variants within the same model can use different starters.
Can I fit a 1.4 kW starter in place of this 1.2 kW unit?
Only if the mounting, pinion and terminal layout are identical. A higher rating does not compensate for a mismatched pinion.
How can I tell whether the starter or the battery is at fault?
Measure battery voltage during cranking. A healthy battery that drops sharply under load, combined with slow cranking, points to the starter drawing excessive current.

