alternator，93161735，TG15C058，0986080420，114509，0986080420，114509，CAL10302,CAL10302ES,CAL10302GS，CAL10302OS，CAL10302RS,CAL15340, CAL15340AS.CAL15340ES， TG15C058, 93161735, 8200404459,ALT590CP，CAL15340OS. CAL15340RS，DRA0339，4431340.93161735，for Nissan

The installation method of the Nissan 12V generator may vary slightly depending on the model. The following takes common Nissan models as an example to introduce the general installation steps:Preparation work: •  Park the vehicle steadily and turn off the engine: Park the vehicle on a flat and safe ground, pull up the handbrake, turn off the engine, and wait for a period of time to let the engine cool down to prevent scalding.  •  Disconnect the power supply: Locate the battery, first remove the negative terminal of the battery to cut off the power supply of the entire vehicle, so as to avoid electric shock or short circuit during operation.  •  Prepare tools: Prepare common tools such as wrenches, sockets, torque wrenches, etc.Removing the old generator: Removing the generator belt: Loosen the fixing bolt of the belt tensioner (usually located near the generator), then loosen the adjusting bolt to slacken the belt, and then remove the belt from the generator pulley and other related components.Disconnecting the electrical connections: Unplug the generator signal wire plug, use a wrench or socket to loosen the generator positive wire bolt, and remove the positive wire. Be sure to mark them properly for correct reconnection later.Removing the fixing bolts: Locate the generator's fixing bolts, which are usually positioned at different places such as top and bottom or front and rear. Use the appropriate tools to loosen and remove these bolts.Taking out the old generator: Carefully take out the old generator from its installation position, taking care not to damage surrounding components or wires.Installing a new generator: Clean the mounting surface: Clean the surface where the generator will be installed, removing oil stains, rust, and impurities to ensure the mounting surface is flat and clean, so that the new generator can be installed stably with good contact.Install the new generator: Align the new generator with the mounting holes, slowly place it into the installation position, and ensure all bolt holes are accurately aligned.Install the fixing bolts: Insert the fixing bolts into the corresponding holes, hand-tighten them a few turns first, then gradually tighten them to the torque value specified in the maintenance manual using a torque wrench.Connect the electrical circuits: According to the marks made earlier, plug the generator signal wire connector back into its original position, tighten the generator positive wire bolt, and ensure the connection is secure.Install the generator belt: Properly install the belt onto the generator pulley and other related pulleys (such as the crankshaft pulley, water pump pulley, etc.), then adjust the belt tension by pressing down the generator through the adjusting bolt of the belt tensioner. Generally, a suitable tension is when the belt can be easily pulled to approximately 90 degrees by hand.Inspection and Testing: •  Reconnect the negative battery terminal: After confirming that all installation steps are correct, reconnect the negative battery cable to the battery and tighten the nut.  •  Start the vehicle: Start the engine and observe whether the charging indicator light on the dashboard turns off normally. At the same time, use a multimeter to measure the battery voltage; under normal circumstances, it should be between 13.5V and 14.5V to ensure that the generator can generate electricity normally.  •  Check the operation status: During the operation of the vehicle, pay attention to whether there is any abnormal noise in the engine compartment, and check whether the various connection parts of the generator are loose, overheating, etc.

When installing a Nissan 12V generator, in addition to the installation steps mentioned earlier, there are the following precautions:Safety aspects: •  Ensure power-off operation: Before disassembling and installing the generator, be sure to disconnect the negative cable of the battery first to prevent electric shock accidents or damage to electrical equipment due to short circuits during operation.  •  Prevent tools from slipping: Hold tools firmly when using them to avoid tools slipping and injuring your feet or damaging other parts of the vehicle. If you need to work under the vehicle, use a jack and safety stands to stably support the vehicle to ensure safety.Component Inspection and Selection: •  Inspect the generator's appearance: Before installing a new generator, check its appearance for damage, such as cracks in the casing, loose terminals, etc., to ensure the generator itself is in good quality.  •  Choose regular accessories: Try to select generators or accessories produced by regular manufacturers to ensure their quality and performance meet the vehicle's requirements, and avoid using inferior accessories which may cause the generator to work abnormally or shorten its service life.Regarding installation operations: •  Clean the installation site: The surface of the installation location should be cleaned thoroughly to remove oil stains, rust, and impurities, etc., to ensure the generator is installed stably with good contact, and at the same time, prevent impurities from entering the interior of the generator and affecting its performance.  •  Pay attention to the bolt tightening torque: Use a torque wrench to tighten the fixing bolts according to the torque value specified in the maintenance manual. The bolt torque may vary for different vehicle models. For example, the tightening torque for the fixing nuts of the upper fixing bolt and the lower through bolt of the generator in some Nissan Lannia models is generally 23 Newton-meters, and the tightening torque for the fixing nut of the positive wire is 18 Newton-meters. Over-tightening the bolts may damage the threads or the generator housing, while under-tightening may cause the generator to loosen, produce abnormal noises, or even fall off.Avoid damaging the lines: When disconnecting and connecting electrical lines, operate with caution. Avoid excessive pulling or bending of the wires to prevent breakage of the internal conductors or damage to the insulation layer. At the same time, ensure that the plug connections are secure to avoid loosening or poor contact, which may cause abnormal operation of the generator or an alarm from the charging indicator light.  •  Correctly connect the terminals: Clearly understand the markings and functions of each terminal on the generator and connect them in the correct way. For example, "B+" should be connected to the positive pole of the battery, and "N" (neutral point) should be connected to the control circuit of the charging indicator light, etc. Incorrect connections may damage the generator or related electrical equipment.Precautions for installing the belt: When installing the generator belt, ensure that the belt is correctly installed on each pulley and that the tension is appropriate. If the belt is too loose, it may cause "slip" in the pulley rotation speed, leading to problems such as insufficient power generation and battery depletion. If the belt is too tight, it will increase the bearing load torque and shorten the service life of the bearing. Generally, a suitable tension is when the belt can be easily pulled to approximately 90 degrees by hand.ost-installation inspection aspects: •  Check installation firmness: After the installation is completed, recheck whether the fixing bolts of the generator are tightened and whether all connecting components are properly installed to ensure that the generator will not loosen during vehicle operation.  •  Conduct power generation test: After reconnecting the negative cable of the battery, start the engine and observe whether the charging indicator light on the instrument panel turns off normally. At the same time, use a multimeter to measure the battery voltage, which should normally be between 13.5V-14.5V to confirm that the generator can generate electricity normally. In addition, after the vehicle has been running for a period of time, you can touch the generator housing to check for overheating. If there is any abnormality, stop the machine for inspection in time.

References：The content you mentioned regarding the installation precautions for the Nissan 12V generator also does not have a specific, single source; it is summarized based on various automotive repair knowledge and experience. These precautions mainly come from the following sources: • Automotive repair manuals: The official repair manuals for various Nissan models released by Nissan Motor Company will detail the generator installation steps, technical requirements, and related precautions, such as bolt tightening torque and component installation sequence. These are important bases to ensure the correct installation and normal operation of the generator.Professional automotive repair websites and platforms: Professional automotive websites and platforms such as Autohome and Auto Master have many maintenance technicians and car enthusiasts who share their maintenance experiences, tips, and precautions regarding generator installation. They have accumulated a great deal of practical experience in actual maintenance work, and the content they share is highly practical.  •  Automotive parts supplier materials: Some regular automotive parts suppliers, when providing Nissan generator parts, also attach relevant installation instructions and precautions to help users correctly install and use the parts, ensuring their performance and quality.