Alternator 1649066 0124655014 0986049780 MX265，MX300，MX340，MX375，MX300S 0124655014.0124655293.0124655294，1976292 01246554050124655406，0986049780，1927312. for Daff CF85.360 12900ccm 5.47034

The installation method of the Daf 24V generator is similar to that of a general 24V generator. The specific steps are as follows: •  Determine the installation location: Choose a place with good ventilation, easy operation and maintenance. Ensure that the installation foundation is solid and reliable, meeting the generator installation requirements.  •  Fix the generator: Fix an angle iron on the side of the engine, install the generator on the angle iron, and fasten it with bolts to ensure that the generator is installed firmly and stably.  •  Connect the lines: The Daf 24V generator usually has four pins, namely B+, D+, W, and E. Among them, B+ represents the positive pole of the battery and should be connected to the positive pole of the vehicle battery; D+ corresponds to the positive pole of the regulator and needs to be connected to the positive pole of the regulator; W is the negative pole of the regulator and should be connected to the negative pole of the regulator; E is connected to the negative pole of the engine body and should be connected to the vehicle's ground wire.Install the belt or chain: Use a belt or chain to connect the generator to the crankshaft, ensuring the connection is secure and the transmission functions properly.  •  Check the installation quality: After installation, check whether all components of the generator are securely installed, whether the wiring connections are correct, and whether there are any loose or poor contact conditions.

When installing the Daf 24V generator, the following precautions should be noted:Selection of installation location •  A well-ventilated place should be chosen. If installed indoors, it is necessary to ensure there are sufficient air inlets and outlets to prevent the generator from overheating, which would affect its performance and service life.  •  A flat and stable ground should be selected to ensure that the generator will not shake after installation. At the same time, it should be easy to operate and maintain, with sufficient space left around it.Foundation and Fixation •  The installation foundation should be solid and reliable. If necessary, the ground can be hardened to ensure that the foundation can bear the weight of the generator and the vibration during operation.  •  Use appropriate brackets and bolts to fix the generator, ensure it is firmly fixed, and the bolt tightening torque should meet the specified requirements to prevent the generator from loosening during operation.Circuit Connection •  Clarify the connection method for the four pins of the generator (B+, D+, W, E). B+ is connected to the positive pole of the battery, D+ to the positive pole of the regulator, W to the negative pole of the regulator, and E to the negative pole of the engine body.  •  Ensure that the circuit connections are firm and have good contact. Use cables of appropriate specifications to avoid problems such as heating and sparking caused by excessively thin cables or poor connections.  •  Pay attention to preventing wrong connections during wiring to avoid damaging the generator or other related equipment.Installation of belts or chains •  When installing a belt or chain, ensure that its tension is appropriate. If it is too loose, the belt or chain will slip, affecting the generator's rotational speed and power generation efficiency; if it is too tight, it will increase the load on the generator bearings and crankshaft, shortening the service life of the components.  •  Check the wear condition of the belt or chain. If there is severe wear or damage, it should be replaced in a timely manner.Safe Operation •  During the installation process, appropriate safety equipment and tools should be used, such as wearing gloves, to avoid injury.  •  Operate strictly in accordance with the generator's installation instructions and operation manual, and do not arbitrarily change the installation steps or parameters.  •  Before installation, the relevant power supply should be disconnected to prevent electric shock accidents.   Post-installation Inspection •  After the installation is completed, a comprehensive inspection of the generator should be carried out, including checking whether all components are installed correctly, whether the bolts are tightened, and whether the pipe connections are sealed.  •  Conduct a test run to observe whether the generator operates normally, whether there are abnormal noises, vibrations, or overheating, and at the same time check whether the voltage and current output are stable within the normal range.

References：The above content regarding the installation precautions for the Daf 24V generator does not have a clear single source. It is a synthesis of key knowledge points from multiple relevant documents and websites. For example, the connection methods for generator pins (B+, D+, W, E) in the wiring connections refer to relevant content from Autohome. The precautions for installation location selection, foundation and fixing, and safe operation are consistent with the general requirements for generator installation technology, such as those mentioned in the "Generator Installation Technology" document in Renren Library. The precautions for belt or chain installation have similar expressions in the content about the installation of Fengdu generators on Autohome.