Alternator 37300-3F020 1042106190，1042106191，373003F020 ALN6191AN，ALN6191BA，ALN6191BS ALN6191UX，ALN6191ZD，ALN6191RB for Hyundai

The following are the general installation steps for a modern 12V starter motor:Preparation before installationTool preparation: Prepare common tools such as socket wrenches, torque wrenches, screwdrivers, etc. Specialized starter motor removal tools may also be required.Component inspection: Check the new starter motor for any external damage and confirm that its model and specifications match the vehicle. Meanwhile, clean the dust, debris, and oil stains around the starter motor installation position to ensure the mounting surface is clean and flat.Vehicle power off: Disconnect the negative cable of the battery to prevent short circuits during installation and ensure operational safety.Identify the starter motor position: The starter motor is usually located at the junction of the engine and transmission, near the flywheel housing. It may be necessary to first remove some components that hinder operation, such as the engine guard, air filter duct, etc., to obtain sufficient operating space.Determine the position of the starter motor: The starter motor is usually located at the junction of the engine and the transmission, near the flywheel housing. It may be necessary to first remove some components that hinder operation, such as the engine guard and air filter duct, to obtain sufficient operating space.  •  Install the starter motor: Align the new starter motor with the mounting holes, place it in slowly, and ensure that the gears of the starter motor properly mesh with the flywheel ring gear. Then screw in the fixing bolts and tighten them to the specified torque using a torque wrench. The torque requirements may vary for different vehicle models, generally around 30-45N・m. For specifics, refer to the vehicle's repair manual.Connecting electrical circuits: Insert the wiring harness plug of the starter into the corresponding socket of the starter, ensuring a firm connection without looseness. At the same time, properly connect the power cord of the starter. Usually, the cable connected to the positive pole of the battery is correctly installed on the corresponding terminal of the starter, and the nut is tightened. The tightening torque of the nut must also comply with the regulations.  •  Inspection and arrangement: After installation, check again whether the fixing bolts of the starter are tightened and whether the electrical connections are secure. If any components were removed, they need to be reinstalled as they were.Post-installation Test: Reconnect the negative cable of the battery, turn on the ignition switch, attempt to start the vehicle, and observe whether the starter can operate normally, with any abnormal noises or vibrations. If the starter operates normally and can smoothly drive the engine to start, it indicates that the installation is successful; if there are abnormal situations, it is necessary to promptly troubleshoot the problem, such as checking whether the wiring connections are correct and whether the starter is securely fixed.

When installing a modern 12V starter motor, here are some precautions to note:Preparation and Inspection Before Installation •  Confirm Specification Matching: It is essential to ensure that the specifications of the new starter motor, such as voltage, power, and model, are fully compatible with the vehicle; otherwise, it may not be installed or function properly.  •  Inspect Related Components: Carefully check whether the engine flywheel ring gear has damages such as wear or broken teeth. If there is a problem with the ring gear, it needs to be repaired or replaced in a timely manner to avoid affecting the normal operation of the starter motor. At the same time, thoroughly clean the oil stains, rust, etc., on the starter motor mounting surface and the flange spigot to ensure the mounting surface is flat and clean for good contact.Vehicle power off: Ensure to disconnect the negative cable of the battery first to prevent short circuits during installation, ensuring the safety of the operator and the integrity of the vehicle's electrical system.Key operational points during installation •  Avoid damaging components: During the entire installation process, it is strictly prohibited to strike the starter with tools such as hammers and wrenches. For components with tight fits, professional pulling and pressing tools should be used for separation and installation to prevent damage to components caused by external impact.  •  Ensure accurate installation position: The installation center of the starter must be aligned with the installation center of the engine. The bolts fixing the starter need to be tightened evenly and symmetrically. Do not tighten one bolt first, as this may cause the installation center to shift. After the starter is fixed, do not use tools to forcibly pry it, so as not to damage the installation contact surface and centering.Correctly connect the circuits: When connecting the electrical circuits of the starter, ensure that the plugs and sockets are firmly connected without any looseness or exposed parts to prevent the risk of short circuits or electric shocks. The tightening torque of the nuts on the solenoid switch terminals must comply with the regulations. Excessively low torque will cause the wire harness to loosen, leading to overheating, affecting starting performance, and even causing arcing and burning. Excessively high torque may break the terminals.  •  Make proper marks and records: If replacing the starter, carefully mark the positions and connection methods of the components when removing the old starter, such as the positions of circuit connections and the installation sequence of bolts, to ensure accurate reinstallation when installing the new starter.Testing and Inspection After Installation •  Conduct Operation Test: After the installation is completed and the negative cable of the battery is reconnected, first conduct an operation test on the test bench (if there is no condition to test on the test bench, try to start it on the vehicle). Power on the starter and observe whether it works normally, and whether there are abnormal noises, vibrations, etc. If any abnormality occurs, troubleshoot in a timely manner, such as checking whether the wiring connections and starter fixing are normal.  •  Check Tools and Debris: Carefully check whether there are any tools or debris left in the engine compartment to avoid potential safety hazards during vehicle operation.

References：The content you mentioned regarding the installation precautions for modern 12V starters is mainly based on a comprehensive reference to the following common sources of automotive repair knowledge: • Automotive professional websites: There are many Q&A and technical articles on starter installation and maintenance on Autohome. These articles mention precautions such as avoiding using tools like hammers to strike components during starter installation and disconnecting the negative terminal of the battery before disassembly. PCauto also has relevant materials, emphasizing key points such as confirming that the starter model matches the vehicle before installation and tightening bolts to the specified torque during installation. The content on these websites usually comes from users' practical experience sharing and professional knowledge of maintenance technicians, providing rich materials for summarizing starter installation precautions.Automobile Maintenance Manual: The official maintenance manual for modern automobiles is a very important source of information. It contains authoritative content such as detailed specifications, steps, torque requirements, and precautions for the installation of starters in various modern vehicle models. Although the passage you saw is not a direct copy of the original manual, the standards and requirements related to starter installation in it are all organized and summarized based on the maintenance manual.  •  Other Technical Materials: Some websites like Daowen Network also have articles on the precautions for using and maintaining automobile starters, mentioning aspects such as the need for a clean starter mounting surface and the tightening torque of the solenoid switch terminal nuts. In addition, relevant experience exchanges and technical documents can be found on some automobile maintenance technical forums and document sharing platforms. They elaborate on the precautions for starter installation from different perspectives, providing supplements for the summary of related content.